Chucks & Jaws

Products • June 25, 2021

Standard Type, F Type, R Type Chucks

To minimize machine downtime and provide operator safety, these Hydraulic Chucks use a simple hex wrench that requires only two to three turns for both clamping and unclamping. Tightening is complete when the clamping screw hits the bottom; controlling tightening torque is not needed. Once a Hydraulic Chuck is centered, the runout will not vary, even if a cutting tool is changed repeatedly. Runout of fewer than three microns at four times diameter can be achieved.

Products • June 23, 2021

TiNox-Cut End Mills

TiNox-Cut End Mills are made from premium ultra-fine micro grain solid carbide with a maximized transverse rupture strength for high impact applications, and produce impressive results compared to conventional end mills. Advanced PVD-applied multi-layered coatings withstand excessive heat and provide superb wear resistance for longer tool life, and tool geometry is designed to produce minimal vibration when machining tough materials.

Products • June 4, 2021

BP Chuck

Ideal for CNC lathe applications, BP's large through hole provides tremendous flexibility for virtually any application where a standard chuck is used including: O.D. and I.D. clamping, bar stock clamping and shaft clamping. Easily convert BP to a collet chuck using collet pads for small diameter parts. n

Products • May 25, 2021

Type 01 ER Collet Chuck Standard Adapter

For machining close to the O.D. or I.D. of a workpiece, the Type 01 Adapter extends drills or endmills away from the face of the toolholder for much needed additional reach. Plus, the adapters allow for offline tool presetting for the next job while the machine continues to work uninterrupted.

Products • March 31, 2021

Chip Blower

The Chip Blower automates in-machine cleaning of coolant and chips by delivering high-volume air flow with spindle rotation. When not in use, the Chip Blower fits easily into any automatic tool change system for vertical, horizontal or multi-tasking machining centers. The Chip Blower can be used with automatic tool changers and programmed into a machining cycle, helping to improve machine utilization and increase productivity. The Chip Blower complements the solid construction, fixed blade ChipFan.

Products • February 3, 2021

CentroteX S Clamping Device Change-Over System

The mini version has all the proven centroteX technology, however with an additional advantage: Actuation takes place with just one screw; thus, you save even more set-up time, and this system was designed to enable a robot to quickly change the clamping device. With lesser tightening torque than is required with the large variant, the centroteX M, the centroteX S can be assembled more quickly and this is executed with the highest repeatability and at the same time it also offers more ergonomic operation.

Products • January 22, 2021

ZeroAct Workpiece Positioning System

With an ultralow profile of 40 mm and extremely flat design, ZeroAct is ideal for any zero-point application especially those where the z-axis travel of the spindle is critical. The ZeroAct features rapid open and closing of the modules and simultaneous actuation with one simple twist of the wrist generating 15kN clamp force. Easily actuate workpieces onto a table or adapter with a low stack-up of 38.1 mm greatly increasing the z-axis travel.

Products • January 15, 2021

GYROFLEX Ultimate Multitasking Machine

The GYROFLEX offers the flexibility to meet a variety of production demands, from low production volume and parts prototyping to high-volume and high-mixed production. A single GYROFLEX requires reduced setup and changeover times and completes complex parts efficiently and accurately.

Products • December 17, 2020

Lynx 2600SY Compact Turning Center

The Lynx 2600SY is designed with a rigid bed structure and incorporates roller type LM guides for all axes. The maximum turning diameter is 14.9" and the maximum turning length is 24", and the main spindle incorporates a 10" chuck while the sub-spindle handles either a 6- or 8-inch chuck size. The main spindle has a speed of 3,500 r/min (25HP) while the sub-spindle turns at 4,500 r/min (15HP), making quick work of complex parts. The Y-axis travel is 4.13", and a 12 station servo-driven BMT tool turret with a half index feature (24 positions) is standard.

Products • November 25, 2020

Pressure-Lok Air Chuck

Northfield's engineering team has developed a brand-new chucking system that requires NO air tubes or hoses. This Pressure-Lok™ air chuck is charged with air by a special handle and holds air pressure for over 2 weeks. These chucks can be mounted to rotary tables with no thru-hole, tombstones, pallets, transfer systems, etc.

Products • November 7, 2020

MM e-motion Power Chuck

Each jaw of the MM e-motion is independently controlled and monitored by an individual electro-mechanical drive, which allows for many clamping functions including self-centering, compensating, and individual jaw movement all within one fully automated chuck.

Products • October 22, 2020

VGi20A Ball Screw Nut Grinding Multitasking Machine

With five axes of motion and storage for 40 tools, the machine can grind thread grooves and also machine the nut circumference, end surface, key grooves, and return tube holes in a single setup. In addition to producing large savings in manufacturing time, elimination of setup changeovers also assures exact phase alignment of thread grooves and return tube holes. A standard touch probe enables automatic pre-processing phase alignment of the thread groove and wheel.n