Prototyp TMC thread mill

March 12, 2012
Prototyp TMC thread mill

To thread a hole and countersink it in one operation, Walter USA LLC, Waukesha, Wis., (www.walter-tools.com/us) introduced a new version of the Prototyp TMC thread mill with a 90° countersink. "A lot of times it's cost-prohibitive to order a step drill, for example, or have a separate countersinking operation," said Mark Hemmerling, Walter's director of marketing.

 

Other enhancements include a wear-resistant and tough ultrafine-grain carbide substrate, a 27° helix with a shortened flute runout for effective chip evacuation when cutting a variety of materials, through-coolant for threads down to M4 and a multilayer TiCN coating that reportedly permits higher cutting speeds and longer tool life. The tools are also available uncoated and can produce threads from M3 to M16. The tools have an aggressive rake angle and can thread material as hard as 48 HRC.

 

In laboratory comparisons with similar tools, the company reported that the new TMC thread mill lasts 50 to 100 percent longer. For example, an automotive and racing company applied the tool to mill M4 threads 2 diameter deep in control arms made of 300-M steel, which has a tensile strength of 217,550 psi. With the TMC thread mill, the company achieved a 200-sfm cutting speed and 0.0007" feed per tooth and increased the number of threads cut during a set amount of time from 80 to 145—an 81 percent increase.

 

In another application, a contract manufacturer machining coupling flanges made of 6150 spring steel, which has a tensile strength of 152,280 psi, cut ½"-deep M10 threads with a TMC tool. Machining parameters were 220 sfm and a 0.0014" feed per tooth. The previous tool cut 120 threads during a set amount of time compared to almost 550 threads for the TMC.

 

The latest version of the company's TEC-CSS tool selection and cutting date software, Version 10.3, contains optimized values for the TMC thread mill with countersink. The online software is available free of charge and recommends a tool based on the application, workpiece material and its hardness. "It lets you know what tools can be used as well as the speeds and feeds, estimated tool life and estimated cost per part based on your hourly shop rate," Hemmerling said. "We launch two updates per year to coincide with new product introductions."

Related Glossary Terms

  • countersink

    countersink

    Tool that cuts a sloped depression at the top of a hole to permit a screw head or other object to rest flush with the surface of the workpiece.

  • countersinking

    countersinking

    Cutting a beveled edge at the entrance of a hole so a screw head sits flush with the workpiece surface.

  • cutting speed

    cutting speed

    Tangential velocity on the surface of the tool or workpiece at the cutting interface. The formula for cutting speed (sfm) is tool diameter 5 0.26 5 spindle speed (rpm). The formula for feed per tooth (fpt) is table feed (ipm)/number of flutes/spindle speed (rpm). The formula for spindle speed (rpm) is cutting speed (sfm) 5 3.82/tool diameter. The formula for table feed (ipm) is feed per tooth (ftp) 5 number of tool flutes 5 spindle speed (rpm).

  • feed

    feed

    Rate of change of position of the tool as a whole, relative to the workpiece while cutting.

  • hardness

    hardness

    Hardness is a measure of the resistance of a material to surface indentation or abrasion. There is no absolute scale for hardness. In order to express hardness quantitatively, each type of test has its own scale, which defines hardness. Indentation hardness obtained through static methods is measured by Brinell, Rockwell, Vickers and Knoop tests. Hardness without indentation is measured by a dynamic method, known as the Scleroscope test.

  • milling machine ( mill)

    milling machine ( mill)

    Runs endmills and arbor-mounted milling cutters. Features include a head with a spindle that drives the cutters; a column, knee and table that provide motion in the three Cartesian axes; and a base that supports the components and houses the cutting-fluid pump and reservoir. The work is mounted on the table and fed into the rotating cutter or endmill to accomplish the milling steps; vertical milling machines also feed endmills into the work by means of a spindle-mounted quill. Models range from small manual machines to big bed-type and duplex mills. All take one of three basic forms: vertical, horizontal or convertible horizontal/vertical. Vertical machines may be knee-type (the table is mounted on a knee that can be elevated) or bed-type (the table is securely supported and only moves horizontally). In general, horizontal machines are bigger and more powerful, while vertical machines are lighter but more versatile and easier to set up and operate.

  • rake

    rake

    Angle of inclination between the face of the cutting tool and the workpiece. If the face of the tool lies in a plane through the axis of the workpiece, the tool is said to have a neutral, or zero, rake. If the inclination of the tool face makes the cutting edge more acute than when the rake angle is zero, the rake is positive. If the inclination of the tool face makes the cutting edge less acute or more blunt than when the rake angle is zero, the rake is negative.

  • tensile strength

    tensile strength

    In tensile testing, the ratio of maximum load to original cross-sectional area. Also called ultimate strength. Compare with yield strength.

  • titanium carbonitride ( TiCN)

    titanium carbonitride ( TiCN)

    Often used as a tool coating. See coated tools.

Additional Products from Walter USA LLC

Walter has introduced two new products for the DC150 drill lineup: 3xD and12xD, both with coolant through the tool body. The DC150 is positioned in the Perform line—a tough, versatile and cost effective Walter Titex family of solid-carbide drills. The two, new length-to-diameter ratio drills join…

Walter has introduced the G1041, a new line of parting blades with a reinforced shank that ensures maximum stability and reliable grooving processes. Suitable for grooving and parting off on all kinds of turning machines, the G1041 features coolant supply through the clamping block, enabling…

Walter has introduced the Walter Prototyp MC251 solid-carbide mill, positioned with the Advance product line designation. Advance referring to mid-level performance and price.

The new Walter Cut G1511-P grooving tool with precision coolant supply, available in 1.0 in. shank sizes, provides long tool life and high productivity, among other benefits. It is suitable for universal use, performing grooving, parting-off, recessing and face grooving with GX insert cutting…

Cast iron drilling has taken a significant step forward with an expanded insert range for new diameters in the high-speed Color Select P6005-WKK45C grade for Xtra·tec B401x point drills. These new inserts are available in diameters up to 1.50 in. (37.99 mm). With this expansion, the grade specially…

The new MC341 Supreme carbide shoulder/slot milling cutter from Walter is specially designed for extended tool life when machining steel and stainless steels. According to the company, yhe cutter delivers exceptional tool life, plus performance improvements of up to 100 percent thanks to the…

Walter says it has unveiled a technology that promises to dramatically improve machining effectiveness. Called Tiger·tec Gold, it is the latest iteration of Walter’s successful line of Tiger·tec and Tiger·tec Silver coatings.

Walter has introduced its new Prototyp Advance line of solid-carbide milling tools for universal application. The new Advance milling cutter line consisting of six cutter types and 250 line items, each reportedly providing the ideal balance of hardness and toughness for the widest possible…

Walter has launched a major extension of its turning geometry program with new products that bring Walter precision and reliability to a range of new applications. Extensions include the FM4 positive inserts.

Walter has expanded its successful DC170 Supreme internally cooled, solid-carbide drill with the introduction of two new sizes, the 25xDc and 30xDc. These sizes extend the drill line, aimed at ISO material groups P, K, and H, to new depths, while keeping the performance enhancing benefits of the…

PRODUCTS

11/20/2024
Jorgensen Conveyor and Filtration Solutions, Mequon, Wisconsin, highlighted its distinctive…

10/23/2024
The Starrett AVR400 offers full CNC capabilities including X-Y-Z positioning and comprehensive zoom…

10/23/2024
TIN Coated Thread Gages have high dimensionally stable HSS construction with TIN coating that…