BIG KAISER introduces two versions of the C-Centering Cutter, a multifunction cutter capable of spot drilling, centering and chamfering. The C-Centering Cutter is an indexable cutter that uses a specialized insert that can start a hole from a solid piece, something extremely difficult to do. It can also perform spot drilling and 90-degree chamfering at the same time or can strictly be used for hole chamfering.
During spot drilling, the insert nose radius can be easily chipped with general cutters since the center has a peripheral speed of zero. The coolant hole in the C-Centering Cutter allows cooling of the cutting edge, which reaches high temperatures during spot drilling, and enables immediate chip evacuation. This prevents chipping during spot drilling.
A benefit of indexable tools is that its life is significantly extended. Once a carbide tool is worn out, there is no other use to it and ends up being thrown away. With an indexable cutter, a small insert can be replaced when worn out, so the cutter body can be reused multiple times.
The new version of this tool is a three-insert C-Centering Cutter, which is only used for chamfering. This version is perfect for general chamfering and results in a reduction of cycle time over using the single insert version.
1. Process of locating the center of a workpiece to be mounted on centers. 2. Process of mounting the workpiece concentric to the machine spindle. See centers.
Fluid that reduces temperature buildup at the tool/workpiece interface during machining. Normally takes the form of a liquid such as soluble or chemical mixtures (semisynthetic, synthetic) but can be pressurized air or other gas. Because of water’s ability to absorb great quantities of heat, it is widely used as a coolant and vehicle for various cutting compounds, with the water-to-compound ratio varying with the machining task. See cutting fluid; semisynthetic cutting fluid; soluble-oil cutting fluid; synthetic cutting fluid.
As opposed to measuring, printing a label and punching the data into the control, SPI prints a tool label with a QR code at the presetter that’s then read by the SPI module at the machine control. The system can also be configured to send measurements directly into the tool NC’s offset table.
The EWA68 boring head has a travel range of .866” on diameter, and with the smallest insert holder, it covers the range of Ø2.677-3.543”. This means that similar-sized bores on the same part could be produced with a single boring head. With the addition of two larger insert holders, the range can…
Chamfering the entry and exit of 0.80mm to 6.00mm holes can be a tedious, time-consuming process. The Noventa from Sphinx can transform this process using an innovative geometry that improves cycle time, tool life and surface quality.
The Nirox geometry has a degressive helix angle equal to 30 degrees at the point and is designed for accurate and precise hole location up to 9xD. A modern, TiAlSiN based coating allows for enhanced chip and coolant evacuation in difficult to machine and adhesive materials, such as titanium,…
Due to the small sizes of these boring heads, the digital display will no longer be present on the head itself, rather the adjustment value will be shown on a separate mobile device or tablet that has the BIG KAISER App installed. Once connected to the head, the App also can be used to set the…
The HDC jet-through type holders are ideal for high-precision 5-axis machining with maximum RPM of 35,000 and clamping range of ¼” to ½” and fit nearly any application in the automotive, aerospace, medical, and die and mold industries.
The exclusive FLM 3D chip-breaker design is used on PCD-tipped inserts ideal for finishing of aluminum components, where traditional flat-top inserts may produce a large continuous nest of chips that is difficult to remove from the bore and/or tool, even with high-pressure coolant. Three different…
BIG KAISER Precision Tooling is adding more than 30 pressed-geometry carbide inserts for its tools. The new insert design is the result of extensive research and testing.
BIG KAISER has added inch standard sizes for the U.S. market to the production of its BIG-PLUS BBT30 basic arbors (shell mill holders, endmill holders, shrink fit and blanks). The expansion allows for enhancements to the BBT30 program that satisfy demands specific to the North American market.
BIG KAISER has released a new set of insert grades for its indexable tools—C-Cutter Mini, C-Centering Cutter and Fullcut Mill. The new inserts are optimized to extend tool life in stainless steel or aluminum.
PRODUCTS
