Resources

The mill is best suited to machining steel, stainless steel, cast iron, non-ferrous material and materials with difficult cutting properties. This wide range of uses results in lower tooling and administrative costs, as does the fact that its 90° approach angle dramatically decreases the need for finishing operations.

Product May 14, 2020

Lift and Turn Compression Latch EN 5630

The standard parts specialist JW Winco introduces the new Lift and Turn Compression Latch for holding doors, covers and hatches closed. It is operated in two steps with an ergonomic, powder-coated T-handle in black or gray. When folding the T-handle in or out, a stroke of 5 mm is initiated on the rotating latch to generate the required pressure against a door seal.

Product May 14, 2020

ABS and ASA Advanced Materials

Both versatile and impact-resistant, BigRep's new ABS (Acrylonitrile Butadiene Styrene) is perfectly suited for mobility applications and a variety of end-use consumer appliances. Weather- and UV-resistant, BigRep's new ASA (Acrylonitrile Styrene Acrylate) material is a robust, engineering-grade filament with high mechanical resistance, low shrinkage and superior layer adhesion, while also showing a greater heat resistance than even ABS.

Product May 14, 2020

FTMg Multifunctional Sensor

With the measurement of compressed and non-corrosive gases, it reliably displays three parameters at once by measuring the flow, pressure, and temperature. In doing so, it saves the customer money through improved energy management with the reliable detection of leaks. This new flow sensor is also very lightweight and compact, making it ideal for installation in tight spaces.n

Product May 13, 2020

DrillMeister 12xD Drill Body

DrillMeister incorporates a unique self-locking interface that enables simple and secure drill head exchange. Since drill heads can be replaced without having to remove the drill body from the spindle, tool setup time can significantly be reduced, eliminating presetting, offset, and touch-off of the replaced tool.

Product May 13, 2020

NCSIMUL Digital Twin Software Update

NCSIMUL virtually builds the real-life machining environment to avoid errors, decrease set-up times and switch CNC programs between machines. nnThe 2021 release features a new comparison mode that detects excessive material during a fast and hidden simulation.

Product May 13, 2020

Dry and Wet Cleaning Modules on FlexMove Conveyors

Designed for FlexMove conveyors, the Dry Cleaning Module provides continuous cleaning of conveyor chain for applications involving powder, dust and other dry contaminates, whereas the Wet Cleaning Module, which are designed for FlexMove stainless steel conveyors, provides uninterrupted cleaning of conveyor chain for applications with liquid, product overfill or package breakage.n

Product May 13, 2020

10×12 mm TungTurn-Jet Toolholders

TungTurn-Jet toolholders deliver coolant strategically to the optimum position close to the cutting point of the insert. This significantly improves chip control when machining exotic materials that are prone to smearing by effectively breaking the chips into pieces and guiding them away from the cut, which was difficult using a traditional external coolant nozzle method.

Product May 13, 2020

BearingStar 90

Due to the extremely short auxiliary process time of 0.9 seconds, the BearingStar 90 is currently able to achieve the quickest roller bearings finish processing in the world. The floor to floor time can be a sensational 3.5 seconds under the conditions of a direct link with an upstream grinding machine, for example, a deep groove ball bearing of an outer and inner ring Type 625.

Product May 12, 2020

MicroStar iQ

The 8 station machine for the combination processing doesn't just ensure 100% compliance of all drawing dimensions for highly precise workpieces, but also the consolidation of the process stream. It generates significant cost savings. Oscillation sensors control the sensors and also the quality of the processes.

Product May 11, 2020

Chip Breaker Inserts

The exclusive FLM 3D chip-breaker design is used on PCD-tipped inserts ideal for finishing of aluminum components, where traditional flat-top inserts may produce a large continuous nest of chips that is difficult to remove from the bore and/or tool, even with high-pressure coolant.

News May 7, 2020

Forest City Gear Co. donates $3,100 to Rockford Rescue Mission

ROSCOE, IL (May 5, 2020) - Forest City Gear Co. is proud to announce that its employees have raised $1,300 to support Rockford Rescue Mission's efforts to respond to the increased need brought on by the COVID-19 pandemic. Forest City Gear committed to match employee donations dollar for dollar, raising the total for this most recent fundraiser to $2,600.

Keep scrolling

« Previous 1 … 372 373 374 375 376 … 1,440 Next »

Machining Fundamentals & Tooling References

Process Spotlights & Manufacturing Systems

Do more with CTE

Keep exploring

Browse results

Explore

Address:

Follow